LedgerSMB
The foundation for your business
Xboxboy, I am trying to understand your host network setup. As an example, here is my firewall network configuration supporting two VM's. It's not everything, but is what is required to run the VMs.
My brctl on the firewall:
[root@wbofw perl]# brctl show ID matches mac addr for eth1 and eno1
bridge name bridge id STP enabled interfaces
eth1 8000.001e67e0bbd6 no eno1
vnet0
vnet1And the ifconfig from the two VMs running on the firewall system.
[root@yawssys]# ifconfig (sshing into the vnet0 VM) note Mac address is identical to vnet0
[root@yawssys7]# ifconfig (sshing into the vnet1 VM) note Mac address is identical vnet1
eth1: Link encap:Ethernet HWaddr FE:54:00:B7:EA:E1
inet addr:96.10.34.44 Bcast:96.10.34.63 Mask:255.255.255.224
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:108356 errors:0 dropped:0 overruns:0 frame:0
TX packets:168471 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8480160 (8.0 MiB) TX bytes:199696532 (190.4 MiB)
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 96.10.34.50 netmask 255.255.255.224 broadcast 96.10.34.63
inet6 fe80::5054:ff:fee2:af0b prefixlen 64 scopeid 0x20<link>
ether FE:54:00:e2:af:0b txqueuelen 1000 (Ethernet)
RX packets 438230 bytes 223232328 (212.8 MiB)
RX errors 0 dropped 14003 overruns 0 frame 0
TX packets 276326 bytes 137199104 (130.8 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0The nomenclature is slightly different on the systems since they are running different versions of Centos.
I am running KVM virtual machines. They may work differently than your VM's.
I wanted to see your VM ifconfig to see it they align with your host interfaces.
Hope this helps.
Regards, Bill Ott Home: 919-363-0031 Cell: 919-434-7589 Email: Mailto:..hidden.. Website: http://www.theotts.org Profile: http://www.linkedin.com/in/wbottOn 3/24/19 7:44 PM, Gnucash Xboxboy Mageia wrote:
On Mon, Mar 25, 2019 at 1:50 AM bill Ott <..hidden..> wrote:
Can you send me the results of the ifconfig on the VM's host?
Reviewing I noticed. from below
"virbr0 is on 192.168.122.1" which is the wrong octal. it should be 192.168.1.XXX. It may be there because your VM is setting up its own DHCP. But that begs the question of how you are reaching the 192.168.1.188 apache interface on the VM.
If you ssh into the VM and issue an ifconfig there, what is its IP address?
Thanks Bill: Ok, the Host IP has changed, because I didn't have a fixed IP for it: I've now sorted that. So here are the results of 'ifconfig'
enp5s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.106 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::62a4:4cff:fe38:82a9 prefixlen 64 scopeid 0x20<link>
ether 60:a4:4c:38:82:a9 txqueuelen 1000 (Ethernet)
RX packets 2173 bytes 521229 (509.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 176 bytes 19475 (19.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 100 bytes 8648 (8.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 100 bytes 8648 (8.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:da:32:4e txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Regards, Bill Ott Home: 919-363-0031 Cell: 919-434-7589 Email: Mailto:..hidden.. Website: http://www.theotts.org Profile: http://www.linkedin.com/in/wbottOn 3/24/19 1:28 AM, Gnucash Xboxboy Mageia wrote:
On Thu, Mar 21, 2019 at 11:00 PM bill Ott <..hidden..> wrote:
Have you tried temporarily turning off SELinux ("setenforce 0"), then trying to connect? After doing the test, turn SELinux back on with "setenforce 1".
Thanks
Just tried that on the host OS with no change.The debian VM doesn't have SElinux installed, as 'getenforce' and 'sestatus' return command not found.
_______________________________________________
Regards, Bill Ott Home: 919-363-0031 Cell: 919-434-7589 Email: Mailto:..hidden.. Website: http://www.theotts.org Profile: http://www.linkedin.com/in/wbottOn 3/21/19 3:40 AM, Xboxboy Mageia wrote:
Bill,
yes, sorry that is a typo: I meant http://192.168.1.118:5762/setup.pl
Regards,Xboxboy
http://192.168.1.188:5762/setup.pl???? Did you mean http://192.168.1.118:5762/setup.pl?---------- Forwarded message ---------
From: bill Ott <..hidden..>
Date: Thu, Mar 21, 2019 at 1:21 AM
Subject: Re: [ledgersmb-users] Fwd: Production Install, Networking and Setup
To: Xboxboy Mageia <..hidden..>
Regards, Bill Ott Home: 919-363-0031 Cell: 919-434-7589 Email: Mailto:..hidden.. Website: http://www.theotts.org Profile: http://www.linkedin.com/in/wbottOn 3/19/19 9:47 PM, Xboxboy Mageia wrote:
Sorry Bill: I meant to send it to the list :-0
Please see the network info I've added, in response to both Bill and Erik.
On Mon, Mar 18, 2019 at 6:45 PM Xboxboy Mageia <..hidden..> wrote:
Hello,I was sick over Xmas, and since then business has been booming, only now can I have a second look. Thank you all for you help.
On Thu, Jan 10, 2019 at 10:38 AM bill Ott <..hidden..> wrote:
Running "brctl show" w/o/ the quotes on the VM's host will show you the bridge and the interfaces that are connected to it. 'ifconfig" w/o the quotes on the VM's host will show you the all of interfaces.
brctl showbridge name bridge id STP enabled interfacesvirbr0 8000:525400da324e yes virbr0-nic
ifconfig
enp5s0 is on 192.168.1.109lo is on 127.0.0.1
virbr0 is on 192.168.122.1
(sorry can't ssh in at the moment, let me know if you need all the details)
Might help chasing down the problem.
Regards, Bill Ott Home: 919-363-0031 Cell: 919-434-7589 Email: Mailto:..hidden.. Website: http://www.theotts.org Profile: http://www.linkedin.com/in/wbottOn 1/9/19 5:21 PM, Erik Huelsmann wrote:
Hi,
Ok, so the debian install went simply. I used debian 9 (Stretch), without a GUI. 'ip addr' gives 192.168.1.101, which sounds right, as that's my lan, 192.168.1.X.
I then followed the instructions on https://apt.ledgersmb.org/index.html, but I installed version 1.5, and did not add the 'test component', I don't know what that means, sorry.
[snip]
I was able to add the DB admin user where the prompt comes up: Now do I need to reset/config mysql's root user and password also?
So from my desktop I tried to access via firefox 192.168.1.101:5762/setup.pl, but it's unable to connect.
Ok. Are you able to ping that ip address from your desktop? That should indicate if you should expect to be able to connect to the web server as well.
Yes, I can ping the debian VM with "ping 192.168.1.118"I can access the default debian apache web server at 192.168.1.118, but no luck with 192.168.1.188:5762/setup.pl
I have a functioning fedora os VM on 192.168.1.107 with nextcloud working fine.
I have the VM network set to bridged, networking is my downfall, and the other thing I suspect is that I need to open the firewall for the webserver.
Bridged sounds fine. quick question: Is the "eth0" (or enpXs0 with X a number) network on the VM's host part of the bridge? If not, you probably need to enable IP forwarding. Before we go that route, lets start by checking you can 'ping' the address though. (And: can you ping the host that the VM is running on?)
I can ping the host with "ping 192.168.1.109"
_______________________________________________
All advice appreciated.
Regards,
--
Bye,
Erik.
http://efficito.com -- Hosted accounting and ERP.Robust and Flexible. No vendor lock-in.
_______________________________________________ users mailing list ..hidden.. https://lists.ledgersmb.org/mailman/listinfo/users
users mailing list
..hidden..
https://lists.ledgersmb.org/mailman/listinfo/users
_______________________________________________ users mailing list ..hidden.. https://lists.ledgersmb.org/mailman/listinfo/users
_______________________________________________ users mailing list ..hidden.. https://lists.ledgersmb.org/mailman/listinfo/users
users mailing list
..hidden..
https://lists.ledgersmb.org/mailman/listinfo/users
_______________________________________________ users mailing list ..hidden.. https://lists.ledgersmb.org/mailman/listinfo/users
_______________________________________________ users mailing list ..hidden.. https://lists.ledgersmb.org/mailman/listinfo/users
_______________________________________________ users mailing list ..hidden.. https://lists.ledgersmb.org/mailman/listinfo/users